Back to the main page Back to category ElectroHarmonix
musical instrument details
Electro Harmonix EHX 45000 Foot Controller for Looper Pedal NEW FC45000
Estimated price for orientation: 999 $
Category: ElectroHarmonix
Class:
Description Condition: New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition Brand: Electro-Harmonix MPN: FC45000 UPC: 683274011325
Electro Harmonix EHX 45000 Foot Controller for Looper Pedal NEW FC45000
Remote Foot Controller for 45000
The 45000 Foot Controller is a wired remote control for the 45000 Looper, giving your feet direct access to the following controls: Track Select, Record, Play, Loop Up and Loop Down. The 45000 Looper records and plays back up to 100 loops per SDHC card. The 45000 Foot Controller makes it very easy for your feet to navigate through your 100 loops, moving up or down through loops by 1 or 10 at a time; allowing you to seamlessly change loops while playing back. Additionally, the 45000 Foot Controller contains a large dual-digit LED display to clearly indicate your current or next loop at all times. - GETTING STARTED - Connect the 45000 Foot Controller (45000 FC) to your 45000 main unit using a standard 1/4” mono instrument cable. Plug into the jack labeled FOOT CONTROLLER on the 45000 Looper. The other end of the cable should be inserted into the 45000 FC’s jack labeled INPUT. As long as the 45000 main unit is powered up, the digits on the 45000 FC will light up indicating it is ready for use. - DISPLAY AND FOOTSWITCHES - 2-DIGIT LED DISPLAY – shows the currently loaded or selected loop number in the 45000 main unit. The numbers range from 00 to 99. If a loop number contains audio on the SDHC card, the rightmost decimal point on the 45000 FC will light. If the rightmost decimal point is not lit, then that particular loop number is empty. LOOP UP/DOWN Footswitches and LEDs – Pressing the LOOP UP footswitch will increment the loop number by 1. Press the LOOP DOWN footswitch to decrement the loop number by 1. Press and hold either footswitch for approximately half a second to jump up or down by ten loops at a time instead of just one. The loop number can be changed when the 45000 is either idle (stopped) or playing back a loop. You cannot change the loop number when recording or overdubbing the loop. If the 45000 is playing back a loop at the time you press either the LOOP UP or LOOP DOWN footswitches, the 2-digit display on the Foot Controller will blink the new loop number, indicating that the 45000 will change to the blinking loop as soon as the current loop plays out to its endpoint. If the newly selected loop number is empty, it will continue to blink until you stop playback or enter overdub, at which time the loop number will return to the last loop that was loaded. The 45000 remembers the last Play setting for the following parameters of each loop number: TEMPO slider, REVERSE button and OCTAVE button. When you go back to any given loop number, these parameter settings will be reinstated for that loop. The LOOP UP and LOOP DOWN LEDs light up when each associated footswitch is held down. RECORD Footswitch and LED – Pressing the RECORD footswitch on the 45000 FC is equivalent to pressing the RECORD button on the 45000 main unit. Usually pressing the RECORD footswitch toggles between Play and Overdub modes. If you load an empty loop number, pressing the RECORD footswitch will immediately begin recording a new loop (or start the 4-beat count-in when Quantize is enabled). In the situation where you want to create a completely different loop for a loop number that already contains audio, you need to first press the NEW LOOP button on the 45000 main unit, then press the RECORD footswitch on the 45000 FC. The RECORD LED on the 45000 FC mimics the RECORD LED on the 45000 main unit. In addition, the RECORD LED on the 45000 FC lights when the RECORD footswitch is held down. PLAY Footswitch and LED – Pressing the PLAY footswitch on the 45000 FC is equivalent to pressing the PLAY button on the 45000 main unit. Usually pressing the PLAY footswitch will start or stop loop play, though it will also end a loop when recording a new loop. The PLAY LED on the 45000 FC mimics the PLAY LED on the 45000 main unit. In addition the PLAY LED on the 45000 FC lights when the PLAY footswitch is held down. TRACK SELECT Footswitch and LED – Pressing the TRACK SELECT footswitch on the 45000 FC is equivalent to pressing the TRACK SELECT button on the 45000 main unit. You can use the TRACK SELECT footswitch to cycle through the four tracks when recording loops in a live setting without needing to touch the 45000 main unit. The TRACK SELECT LED on the 45000 FC lights up when Track 1 is selected but shuts off when any other track is selected. If Stereo Mode
Description
| Condition: | New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition | Brand: | Electro-Harmonix |
| MPN: | FC45000 | UPC: | 683274011325 |
Electro Harmonix EHX 45000 Foot Controller for Looper Pedal NEW FC45000
Remote Foot Controller for 45000
The 45000 Foot Controller is a wired remote control for the 45000 Looper, giving your feet direct access to the following controls: Track Select, Record, Play, Loop Up and Loop Down. The 45000 Looper records and plays back up to 100 loops per SDHC card. The 45000 Foot Controller makes it very easy for your feet to navigate through your 100 loops, moving up or down through loops by 1 or 10 at a time; allowing you to seamlessly change loops while playing back. Additionally, the 45000 Foot Controller contains a large dual-digit LED display to clearly indicate your current or next loop at all times. - GETTING STARTED - Connect the 45000 Foot Controller (45000 FC) to your 45000 main unit using a standard 1/4” mono instrument cable. Plug into the jack labeled FOOT CONTROLLER on the 45000 Looper. The other end of the cable should be inserted into the 45000 FC’s jack labeled INPUT. As long as the 45000 main unit is powered up, the digits on the 45000 FC will light up indicating it is ready for use. - DISPLAY AND FOOTSWITCHES - 2-DIGIT LED DISPLAY – shows the currently loaded or selected loop number in the 45000 main unit. The numbers range from 00 to 99. If a loop number contains audio on the SDHC card, the rightmost decimal point on the 45000 FC will light. If the rightmost decimal point is not lit, then that particular loop number is empty. LOOP UP/DOWN Footswitches and LEDs – Pressing the LOOP UP footswitch will increment the loop number by 1. Press the LOOP DOWN footswitch to decrement the loop number by 1. Press and hold either footswitch for approximately half a second to jump up or down by ten loops at a time instead of just one. The loop number can be changed when the 45000 is either idle (stopped) or playing back a loop. You cannot change the loop number when recording or overdubbing the loop. If the 45000 is playing back a loop at the time you press either the LOOP UP or LOOP DOWN footswitches, the 2-digit display on the Foot Controller will blink the new loop number, indicating that the 45000 will change to the blinking loop as soon as the current loop plays out to its endpoint. If the newly selected loop number is empty, it will continue to blink until you stop playback or enter overdub, at which time the loop number will return to the last loop that was loaded. The 45000 remembers the last Play setting for the following parameters of each loop number: TEMPO slider, REVERSE button and OCTAVE button. When you go back to any given loop number, these parameter settings will be reinstated for that loop. The LOOP UP and LOOP DOWN LEDs light up when each associated footswitch is held down. RECORD Footswitch and LED – Pressing the RECORD footswitch on the 45000 FC is equivalent to pressing the RECORD button on the 45000 main unit. Usually pressing the RECORD footswitch toggles between Play and Overdub modes. If you load an empty loop number, pressing the RECORD footswitch will immediately begin recording a new loop (or start the 4-beat count-in when Quantize is enabled). In the situation where you want to create a completely different loop for a loop number that already contains audio, you need to first press the NEW LOOP button on the 45000 main unit, then press the RECORD footswitch on the 45000 FC. The RECORD LED on the 45000 FC mimics the RECORD LED on the 45000 main unit. In addition, the RECORD LED on the 45000 FC lights when the RECORD footswitch is held down. PLAY Footswitch and LED – Pressing the PLAY footswitch on the 45000 FC is equivalent to pressing the PLAY button on the 45000 main unit. Usually pressing the PLAY footswitch will start or stop loop play, though it will also end a loop when recording a new loop. The PLAY LED on the 45000 FC mimics the PLAY LED on the 45000 main unit. In addition the PLAY LED on the 45000 FC lights when the PLAY footswitch is held down. TRACK SELECT Footswitch and LED – Pressing the TRACK SELECT footswitch on the 45000 FC is equivalent to pressing the TRACK SELECT button on the 45000 main unit. You can use the TRACK SELECT footswitch to cycle through the four tracks when recording loops in a live setting without needing to touch the 45000 main unit. The TRACK SELECT LED on the 45000 FC lights up when Track 1 is selected but shuts off when any other track is selected. If Stereo Mode
Remote Foot Controller for 45000
The 45000 Foot Controller is a wired remote control for the 45000 Looper, giving your feet direct access to the following controls: Track Select, Record, Play, Loop Up and Loop Down. The 45000 Looper records and plays back up to 100 loops per SDHC card. The 45000 Foot Controller makes it very easy for your feet to navigate through your 100 loops, moving up or down through loops by 1 or 10 at a time; allowing you to seamlessly change loops while playing back. Additionally, the 45000 Foot Controller contains a large dual-digit LED display to clearly indicate your current or next loop at all times. - GETTING STARTED - Connect the 45000 Foot Controller (45000 FC) to your 45000 main unit using a standard 1/4” mono instrument cable. Plug into the jack labeled FOOT CONTROLLER on the 45000 Looper. The other end of the cable should be inserted into the 45000 FC’s jack labeled INPUT. As long as the 45000 main unit is powered up, the digits on the 45000 FC will light up indicating it is ready for use. - DISPLAY AND FOOTSWITCHES - 2-DIGIT LED DISPLAY – shows the currently loaded or selected loop number in the 45000 main unit. The numbers range from 00 to 99. If a loop number contains audio on the SDHC card, the rightmost decimal point on the 45000 FC will light. If the rightmost decimal point is not lit, then that particular loop number is empty. LOOP UP/DOWN Footswitches and LEDs – Pressing the LOOP UP footswitch will increment the loop number by 1. Press the LOOP DOWN footswitch to decrement the loop number by 1. Press and hold either footswitch for approximately half a second to jump up or down by ten loops at a time instead of just one. The loop number can be changed when the 45000 is either idle (stopped) or playing back a loop. You cannot change the loop number when recording or overdubbing the loop. If the 45000 is playing back a loop at the time you press either the LOOP UP or LOOP DOWN footswitches, the 2-digit display on the Foot Controller will blink the new loop number, indicating that the 45000 will change to the blinking loop as soon as the current loop plays out to its endpoint. If the newly selected loop number is empty, it will continue to blink until you stop playback or enter overdub, at which time the loop number will return to the last loop that was loaded. The 45000 remembers the last Play setting for the following parameters of each loop number: TEMPO slider, REVERSE button and OCTAVE button. When you go back to any given loop number, these parameter settings will be reinstated for that loop. The LOOP UP and LOOP DOWN LEDs light up when each associated footswitch is held down. RECORD Footswitch and LED – Pressing the RECORD footswitch on the 45000 FC is equivalent to pressing the RECORD button on the 45000 main unit. Usually pressing the RECORD footswitch toggles between Play and Overdub modes. If you load an empty loop number, pressing the RECORD footswitch will immediately begin recording a new loop (or start the 4-beat count-in when Quantize is enabled). In the situation where you want to create a completely different loop for a loop number that already contains audio, you need to first press the NEW LOOP button on the 45000 main unit, then press the RECORD footswitch on the 45000 FC. The RECORD LED on the 45000 FC mimics the RECORD LED on the 45000 main unit. In addition, the RECORD LED on the 45000 FC lights when the RECORD footswitch is held down. PLAY Footswitch and LED – Pressing the PLAY footswitch on the 45000 FC is equivalent to pressing the PLAY button on the 45000 main unit. Usually pressing the PLAY footswitch will start or stop loop play, though it will also end a loop when recording a new loop. The PLAY LED on the 45000 FC mimics the PLAY LED on the 45000 main unit. In addition the PLAY LED on the 45000 FC lights when the PLAY footswitch is held down. TRACK SELECT Footswitch and LED – Pressing the TRACK SELECT footswitch on the 45000 FC is equivalent to pressing the TRACK SELECT button on the 45000 main unit. You can use the TRACK SELECT footswitch to cycle through the four tracks when recording loops in a live setting without needing to touch the 45000 main unit. The TRACK SELECT LED on the 45000 FC lights up when Track 1 is selected but shuts off when any other track is selected. If Stereo Mode