Back to the main page Back to category IGS Audio Tubeco
musical instrument details
IGS Audio TubeCore 3U Vari-Mu Mastering Compressor Brand New (NIB)
Estimated price for orientation: 2 449 $
Category: IGS Audio Tubeco
Class:
Description Condition: New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition Brand: IGS MPN: Does Not Apply UPC: Does not apply
IGS Audio Tubecore 3U - Vari Mu Mastering CompressorFully symmetric design, from Input to OutputPrecise analog scales and ultra fast VU MetersHard-wired BYPASS switchStepped controlsSidechain HPFMid/Side ProcessingWet/Dry MixerFrequency response +/-0.2dB: 20Hz-20KHzRelease: 0.1s - 4sAttack: 10 - 300 msMax. gain: 35dBXLR input/outputInput - Carnhill transformerOutput - Sowter transformer230V/115V Power optionPower Consumption: 44 WattsDimensions: 19" 3U, 180mm deepExternal power supplyShipping weight: 7 kilos
The Tubecore was designed as a studio mastering compressor. It is built using the 3U enclosure, which gives necessary front panel clarity and makes it easier to replace tubes located at the back. This design is based on the possibility to replace tubes. The user decides how the device should sound. The sound can be changed by changing the tubes in the back of the device. You can achieve the following effects:- 6N1P-EW – standard set of tubes, “standard†compression
- 6BC8/6BZ8 – tight, transparent, punchy compression
- 6386 – legendary compression, by famous twin triode
- 5670 – deep and dark tube compressionAfter replacing the tubes, all that needs to be done is calibrating "Zero" on the VU Meter. You can do this using a small screwdriver on the rear panel of the device. Basic new features of the Tubecore are:
- Sidechain HPF
- MID/SIDE processing
- WET/DRY mixer
- All stepped manipulators
- Engineer’s custom tube set Front panel (from left to right): - VU meter – dB reduction level
- BYPASS/STEREO/MID/SIDE/BYPASS – compressor mode switch, with two Bypass positions
- HPF OFF/60/120 – high pass filter settings for sidechain
- GAIN – signal input level
- ATTACK – 0.1ms to 30ms
- RELEASE – 0,1s to 4s
- THRESHOLD – 0 do -12dB
- OUTPUT – output signal level
- MIX Wet/Dry – compressed to clean signal ratio
- Voltage indicator
- Power switchRear panel (from left to right): - External power supply connector
- OUTPUT – compressor output, XLR sockets, fully balanced
- 6N1P – output tubes
- ZERO METER – VU meter calibration
- 6386/5670 – input tube sockets, user selects
- 6N1P/6BC8 – input tube sockets, user selects
- INPUT – XLR balanced input
Description
| Condition: | New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition | Brand: | IGS |
| MPN: | Does Not Apply | UPC: | Does not apply |
IGS Audio Tubecore 3U - Vari Mu Mastering CompressorFully symmetric design, from Input to OutputPrecise analog scales and ultra fast VU MetersHard-wired BYPASS switchStepped controlsSidechain HPFMid/Side ProcessingWet/Dry MixerFrequency response +/-0.2dB: 20Hz-20KHzRelease: 0.1s - 4sAttack: 10 - 300 msMax. gain: 35dBXLR input/outputInput - Carnhill transformerOutput - Sowter transformer230V/115V Power optionPower Consumption: 44 WattsDimensions: 19" 3U, 180mm deepExternal power supplyShipping weight: 7 kilos
The Tubecore was designed as a studio mastering compressor. It is built using the 3U enclosure, which gives necessary front panel clarity and makes it easier to replace tubes located at the back. This design is based on the possibility to replace tubes. The user decides how the device should sound. The sound can be changed by changing the tubes in the back of the device. You can achieve the following effects:- 6N1P-EW – standard set of tubes, “standard†compression
- 6BC8/6BZ8 – tight, transparent, punchy compression
- 6386 – legendary compression, by famous twin triode
- 5670 – deep and dark tube compressionAfter replacing the tubes, all that needs to be done is calibrating "Zero" on the VU Meter. You can do this using a small screwdriver on the rear panel of the device. Basic new features of the Tubecore are:
- Sidechain HPF
- MID/SIDE processing
- WET/DRY mixer
- All stepped manipulators
- Engineer’s custom tube set Front panel (from left to right): - VU meter – dB reduction level
- BYPASS/STEREO/MID/SIDE/BYPASS – compressor mode switch, with two Bypass positions
- HPF OFF/60/120 – high pass filter settings for sidechain
- GAIN – signal input level
- ATTACK – 0.1ms to 30ms
- RELEASE – 0,1s to 4s
- THRESHOLD – 0 do -12dB
- OUTPUT – output signal level
- MIX Wet/Dry – compressed to clean signal ratio
- Voltage indicator
- Power switchRear panel (from left to right): - External power supply connector
- OUTPUT – compressor output, XLR sockets, fully balanced
- 6N1P – output tubes
- ZERO METER – VU meter calibration
- 6386/5670 – input tube sockets, user selects
- 6N1P/6BC8 – input tube sockets, user selects
- INPUT – XLR balanced input
The Tubecore was designed as a studio mastering compressor. It is built using the 3U enclosure, which gives necessary front panel clarity and makes it easier to replace tubes located at the back. This design is based on the possibility to replace tubes. The user decides how the device should sound. The sound can be changed by changing the tubes in the back of the device. You can achieve the following effects:- 6N1P-EW – standard set of tubes, “standard†compression
- 6BC8/6BZ8 – tight, transparent, punchy compression
- 6386 – legendary compression, by famous twin triode
- 5670 – deep and dark tube compressionAfter replacing the tubes, all that needs to be done is calibrating "Zero" on the VU Meter. You can do this using a small screwdriver on the rear panel of the device. Basic new features of the Tubecore are:
- Sidechain HPF
- MID/SIDE processing
- WET/DRY mixer
- All stepped manipulators
- Engineer’s custom tube set Front panel (from left to right): - VU meter – dB reduction level
- BYPASS/STEREO/MID/SIDE/BYPASS – compressor mode switch, with two Bypass positions
- HPF OFF/60/120 – high pass filter settings for sidechain
- GAIN – signal input level
- ATTACK – 0.1ms to 30ms
- RELEASE – 0,1s to 4s
- THRESHOLD – 0 do -12dB
- OUTPUT – output signal level
- MIX Wet/Dry – compressed to clean signal ratio
- Voltage indicator
- Power switchRear panel (from left to right): - External power supply connector
- OUTPUT – compressor output, XLR sockets, fully balanced
- 6N1P – output tubes
- ZERO METER – VU meter calibration
- 6386/5670 – input tube sockets, user selects
- 6N1P/6BC8 – input tube sockets, user selects
- INPUT – XLR balanced input