Back to the main page Back to category Vintage Pro Audio Equipment
musical instrument details
Yamaha ns-10m studio speakers matching serials w/ yamaha a100a amplifier rare
Estimated price for orientation: 1 200 $
Category: Vintage Pro Audio Equipment
Class:
Description Brand: Yamaha Country/Region of Manufacture: Japan Model: NS-10M and A100a Type: Vintage Speakers/Monitors
This listing is for both Yamaha NS-10M Studio Speakers (pair)
And
Yamaha A100a stereo power amplifier Tested and working. Can provide video proof. The quality on these are amazing. I would go deaf if I turned them up to much. Both are in good condition showing signs of use. The NS-10 is an 8-ohm two-way loudspeaker with a 10.4-litre Sealed cabinet measuring 382 × 215 × 199 millimetres (15.0 × 8.5 × 7.8 in) and weighing 6 kilograms (13.2 lb).[6][5] Its 2.5 cm (0.98 in) particle-board cabinet has a wood veneer skin with seven black finishing layers. The domestic version of the speaker was vertically orientated, and came factory fitted with a grille.[7][6] Its two drivers are a 180 mm paper woofer and a 35 mm soft-domed tweeter.[6][5] The woofer's diaphragm, weighing 3.7 g, is manufactured from a flat sheet of pressed pulp paper. Unconventionally, it is formed into conical shape not through moulding or pressure, but by curling and then gluing the two ends together.[6] Against the black finish of the cabinet, the white bass/mid driver cone is a distinctive and iconic feature of the product.[7][6] The network is second-order passive, crossing over at 2 kHz. The frequency range is quoted from 60 Hz to 20 kHz, and rated power handling is 25–50 W.[6][5]The early version of the speaker has press-down type output terminals; later models had screw terminals. The A100a stereo power amplifier This amp was designed specifically by Yamaha for the NS-10m Studio Monitors. It is the perfect match. High Power In Stereo The A100A puts out 50 continuous watts per channel into 8-ohm loads. Large Power Meters and Clip Indicators Two large, illuminated power meters that provide readout in power (watts into 8 ohms) as well as decibels. Precision clip indicators for each channel warn of peak signal levels that may cause distortion. Independent Output Level Controls Independent front-panel output level controls for the channel A and channel B. Two Types of input Connectors Both RCA-type pin jacks and 1/4" phone jacks on each input. Front-panel Headphone Jack The amp is 100% functional and in beautiful condition. Check out the photos for details.
Description
| Brand: | Yamaha | Country/Region of Manufacture: | Japan |
| Model: | NS-10M and A100a | Type: | Vintage Speakers/Monitors |
This listing is for both Yamaha NS-10M Studio Speakers (pair)
And
Yamaha A100a stereo power amplifier Tested and working. Can provide video proof. The quality on these are amazing. I would go deaf if I turned them up to much. Both are in good condition showing signs of use. The NS-10 is an 8-ohm two-way loudspeaker with a 10.4-litre Sealed cabinet measuring 382 × 215 × 199 millimetres (15.0 × 8.5 × 7.8 in) and weighing 6 kilograms (13.2 lb).[6][5] Its 2.5 cm (0.98 in) particle-board cabinet has a wood veneer skin with seven black finishing layers. The domestic version of the speaker was vertically orientated, and came factory fitted with a grille.[7][6] Its two drivers are a 180 mm paper woofer and a 35 mm soft-domed tweeter.[6][5] The woofer's diaphragm, weighing 3.7 g, is manufactured from a flat sheet of pressed pulp paper. Unconventionally, it is formed into conical shape not through moulding or pressure, but by curling and then gluing the two ends together.[6] Against the black finish of the cabinet, the white bass/mid driver cone is a distinctive and iconic feature of the product.[7][6] The network is second-order passive, crossing over at 2 kHz. The frequency range is quoted from 60 Hz to 20 kHz, and rated power handling is 25–50 W.[6][5]The early version of the speaker has press-down type output terminals; later models had screw terminals. The A100a stereo power amplifier This amp was designed specifically by Yamaha for the NS-10m Studio Monitors. It is the perfect match. High Power In Stereo The A100A puts out 50 continuous watts per channel into 8-ohm loads. Large Power Meters and Clip Indicators Two large, illuminated power meters that provide readout in power (watts into 8 ohms) as well as decibels. Precision clip indicators for each channel warn of peak signal levels that may cause distortion. Independent Output Level Controls Independent front-panel output level controls for the channel A and channel B. Two Types of input Connectors Both RCA-type pin jacks and 1/4" phone jacks on each input. Front-panel Headphone Jack The amp is 100% functional and in beautiful condition. Check out the photos for details.
And
Yamaha A100a stereo power amplifier Tested and working. Can provide video proof. The quality on these are amazing. I would go deaf if I turned them up to much. Both are in good condition showing signs of use. The NS-10 is an 8-ohm two-way loudspeaker with a 10.4-litre Sealed cabinet measuring 382 × 215 × 199 millimetres (15.0 × 8.5 × 7.8 in) and weighing 6 kilograms (13.2 lb).[6][5] Its 2.5 cm (0.98 in) particle-board cabinet has a wood veneer skin with seven black finishing layers. The domestic version of the speaker was vertically orientated, and came factory fitted with a grille.[7][6] Its two drivers are a 180 mm paper woofer and a 35 mm soft-domed tweeter.[6][5] The woofer's diaphragm, weighing 3.7 g, is manufactured from a flat sheet of pressed pulp paper. Unconventionally, it is formed into conical shape not through moulding or pressure, but by curling and then gluing the two ends together.[6] Against the black finish of the cabinet, the white bass/mid driver cone is a distinctive and iconic feature of the product.[7][6] The network is second-order passive, crossing over at 2 kHz. The frequency range is quoted from 60 Hz to 20 kHz, and rated power handling is 25–50 W.[6][5]The early version of the speaker has press-down type output terminals; later models had screw terminals. The A100a stereo power amplifier This amp was designed specifically by Yamaha for the NS-10m Studio Monitors. It is the perfect match. High Power In Stereo The A100A puts out 50 continuous watts per channel into 8-ohm loads. Large Power Meters and Clip Indicators Two large, illuminated power meters that provide readout in power (watts into 8 ohms) as well as decibels. Precision clip indicators for each channel warn of peak signal levels that may cause distortion. Independent Output Level Controls Independent front-panel output level controls for the channel A and channel B. Two Types of input Connectors Both RCA-type pin jacks and 1/4" phone jacks on each input. Front-panel Headphone Jack The amp is 100% functional and in beautiful condition. Check out the photos for details.