MSRP: $2,065 Features & BenefitsBiamp/Full-Range SwitchableOperates down to 90HzIntegrated wave guideArray up to 16 elements10:1 static load factorEasily ground stackablePowered version available ApplicationsTouring applicationsPortable entertainmentTheatersHouses of worshipBallroomsDiscos & clubs The C-208 is loaded with double 8″ LF/MF and a single high energy HF driver. Each enclosure is constructed of high grade birch ply-wood and is custom fitted with steel fly hardware that has been test rated for a 7:1 static load, hanging up to 16 enclosures in a single array. Our user friendly hardware allows for hanging and ground stacking applications, permitting the user to stack up to six enclosures. All C-208 enclosures are hand wired using premium 14 gauge wire and Neutrik brand NL8 connectors. All drivers are built with cast fame baskets for strength and longevity. Our compression drivers have replaceable titanium diaphragms for superb sound quality, performance and durability. We use a standard phase plug design to control the isophasic wave form as well as a wave guide system for smooth coverage and coupling. Our components are designed and built to a commercial standard and have a proven track record on tours ranging from stadiums to festivals of up to 30 shows per month with practically a nonexistent failure rate. All C-208 enclosures are equipped with a removable back panel that can be disconnected and replaced by an internal TVi multi channel “Class D” power amplifier module. Each power amplifier has a built in multi-channel processor that has been chamber tuned for the C-208 to achieve a flat response curve with pre set limiters, DSP and crossover points. One amplified C-208 enclosure will also power one additional non-powered C-208 enclosure in tri amp mode by daisy chaining an NL8 cable.specifications c-208 Biamp/Full-Range Switchable (NL4) 2×8″, 1×1.7″ diaphragm Frequency Response (+/-3 dB) 90 Hz – 19 kHz Program Power (watts) LF-300, LF2-300, HF-130 RMS Power (watts) LF-150, LF2-150, HF-65 SPL & Sensitivity (1w/1m) 126dB / 101dB Coverage Angle 90 x 10 degrees Nominal Impedance Full-Range: 16Ohm, Biamp: HF 8ohm, LF 8ohm Dimensions (HxWxD) 25.27″ x 13″ x 9.64/7.71″ Weight & Material 50.70 lbs 3/4″ birch plywood C-208 Amplification C-208-(500 series) 2 channel amplifier module (Designed to power two or four C-208 enclosures in full-range) A single three channel “ICE” powered class D amplifier module can power two C-208 line array enclosures in biamp mode. Amplifier channel one powers mid frequency one, channel two powers the mid frequency two and channel three powers the high frequency of two enclosures. When two enclosures are powered using a single amplifier module, it is an 8 ohm load for the high frequency and 4 ohm load for each mid frequency channel. The amplifier module has been designed to fit securely into the enclosure and efficiently power itself plus one additional non-powered C-208 by linking an NL4 connector cable. Each C-208 amplifier module is powered by multiple “ICE” power modules and offers an integrated active crossover system along with DSP correction that has been fine tuned in an anechoic chamber to provide the user with chambered flat response. Powered using multiple “ICE” power modulesUltra light weight digital switching technology (8 lbs)Built in DSP correction softwareBuilt in digital crossovers to optimize power and clarityChamber tuned for suggested phasing a flat response correctionDurable and heat resistant design to eliminate pre-mature thermal protectionNon-powered enclosures are connected to powered enclosure with NL4 patch cablesLinkable “Neutrik Power-con” connection capable of 110v or 220v Installation Process When installing the amplifier pack, remove the passive panel on the back of the enclosure by un-screwing the t-nut bolts. Once the passive panel has been removed, connect the amplifier by following the simple color coded diagram provided. Once the amplifier has been properly connected, slide the amplifier module into the enclosure and secure with the t-nut bolts. Link the second non-powered C-208 to the first with standard NL4 patch cable. Amplifiers are powered by a linkable “Neutrik Power-con” connection and capable of 110v or 220v. Amplifiers ordered for a specific voltage must me slightly modified when changing voltage. Please contact a TVi reprehensiv