Back to the main page Back to category Preamps and Channel Strips
musical instrument details
Brand New Vertigo Sound VSP-2 Dual Mic Preamp 1976 - PRE-ORDER - FREE SHIPPING
Estimated price for orientation: 4 790 $
Category: Preamps and Channel Strips
Class:
Description Condition: New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition Brand: Vertigo Sound MPN: Does Not Apply Type: VSP-2 Dual Mic Preamp 1976 UPC: Does not apply
Gain control:
10-position Grayhill Rotaryswitch with 6db step increments. The full range of the unit is 12-72dbFine Gain control:
41 click Alps 0-6db fine gain trim120Hz/off/80hz:
Switch that engages lowcut input filter 12db/oct at 80hz or 120 HZ.Signal & Clip LED:
This LED either indicates Green for a reasonable signal level presence at the output or red for close to Overload.
There is no inbetween orange state to indicate clipping clearly.LED green:
- 6dBu to 19dBu at the output of the VSP-2 >>>> reasonable output levelLED red:
+19dBu at the output of the VSP-2 >>>> close to clipping levelNote: The maximum output of the VSP-2 is +24dbU, the red clipping led indicates the maximum capable input level of most common converters and analog gear.
INSTRUMENT IN:
This is an unbalanced input for guitar, bass, samples, etc. This unbalanced input goes directly to the TWIN OPA input without using any circuitry inbetween. (Real DI Input)
Simply throw the toggle switch and you're off. The output is muted when switching to avoid loud clicks in your monitors.48V :
48V switches ramped phantom power.-20dB:
Pads the input signal 20dB down. The pad does not affect the input impedance of the VSP-2!
The pad circuitry is switched out of the Input stage completley when disabled.Please use the Pad for the gain Settings 12dB-18db-24dB and 30dB only!!! The Pad does not effect the sound of your signal but settings like 54dB with Pad engaged e.G. will worsen your signal to noise ratio.PHASE:
Reverses the polarity of the pre amp's output.
Description
| Condition: | New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition | Brand: | Vertigo Sound |
| MPN: | Does Not Apply | Type: | VSP-2 Dual Mic Preamp 1976 |
| UPC: | Does not apply |
Gain control:
10-position Grayhill Rotaryswitch with 6db step increments. The full range of the unit is 12-72dbFine Gain control:
41 click Alps 0-6db fine gain trim120Hz/off/80hz:
Switch that engages lowcut input filter 12db/oct at 80hz or 120 HZ.Signal & Clip LED:
This LED either indicates Green for a reasonable signal level presence at the output or red for close to Overload.
There is no inbetween orange state to indicate clipping clearly.LED green:
- 6dBu to 19dBu at the output of the VSP-2 >>>> reasonable output levelLED red:
+19dBu at the output of the VSP-2 >>>> close to clipping levelNote: The maximum output of the VSP-2 is +24dbU, the red clipping led indicates the maximum capable input level of most common converters and analog gear.
INSTRUMENT IN:
This is an unbalanced input for guitar, bass, samples, etc. This unbalanced input goes directly to the TWIN OPA input without using any circuitry inbetween. (Real DI Input)
Simply throw the toggle switch and you're off. The output is muted when switching to avoid loud clicks in your monitors.48V :
48V switches ramped phantom power.-20dB:
Pads the input signal 20dB down. The pad does not affect the input impedance of the VSP-2!
The pad circuitry is switched out of the Input stage completley when disabled.Please use the Pad for the gain Settings 12dB-18db-24dB and 30dB only!!! The Pad does not effect the sound of your signal but settings like 54dB with Pad engaged e.G. will worsen your signal to noise ratio.PHASE:
Reverses the polarity of the pre amp's output.
10-position Grayhill Rotaryswitch with 6db step increments. The full range of the unit is 12-72dbFine Gain control:
41 click Alps 0-6db fine gain trim120Hz/off/80hz:
Switch that engages lowcut input filter 12db/oct at 80hz or 120 HZ.Signal & Clip LED:
This LED either indicates Green for a reasonable signal level presence at the output or red for close to Overload.
There is no inbetween orange state to indicate clipping clearly.LED green:
- 6dBu to 19dBu at the output of the VSP-2 >>>> reasonable output levelLED red:
+19dBu at the output of the VSP-2 >>>> close to clipping levelNote: The maximum output of the VSP-2 is +24dbU, the red clipping led indicates the maximum capable input level of most common converters and analog gear.
INSTRUMENT IN:
This is an unbalanced input for guitar, bass, samples, etc. This unbalanced input goes directly to the TWIN OPA input without using any circuitry inbetween. (Real DI Input)
Simply throw the toggle switch and you're off. The output is muted when switching to avoid loud clicks in your monitors.48V :
48V switches ramped phantom power.-20dB:
Pads the input signal 20dB down. The pad does not affect the input impedance of the VSP-2!
The pad circuitry is switched out of the Input stage completley when disabled.Please use the Pad for the gain Settings 12dB-18db-24dB and 30dB only!!! The Pad does not effect the sound of your signal but settings like 54dB with Pad engaged e.G. will worsen your signal to noise ratio.PHASE:
Reverses the polarity of the pre amp's output.